PLC Delta DVP-EH Series

Digital modules (output/input/mix), analog modules (output/input/mix), temperature measurement/control modules, load cell modules, network modules, remote I/O communication modules

Applications :

Remote device monitoring, production line monitoring, printing machine, container filler (recipe application).

Specifications :

• Digital modules (output/input/mix): 8,16, 32, 48 I/O
• Analog modules (output/input/mix): 4 channel, 6 channel inputs (14-bit) / output (12-bit)
• Load cell modules (for EH3-L): Independent dual-channel high speed high accuracy load cell module with 24 bits resolution with 2.5ms response rate
• Temperature measurement modules: conversion time 200ms/channel, overall accuracy +/-0.6%, resolution RTD inputs Pt100 / Pt1000 / Ni100 / Ni1000 3850 PPM/°C, thermocouple inputs DJ, K, R, S, T, E, N type
• Network modules (for EH3-L): EtherNet, DeviceNet, PROFIBUS-DP, CANopen, RS-485, RS-422, BACnet MS/TP
• Remote I/O communication modules (for EH3-L): DeviceNet, PROFIBUS-DP, MODBUS TCP, EtherNet, RS-48

PLC Delta DVP-EC3 Series

EC3 series is the most economical solution for sequential control and communication monitoring and can operate independently, allowing the user to achieve stand-alone monitor, e.g. monitoring phototransistor coupler, proximity switch, optical sensor, indicator and illumination switch. Through serial ports, EC3 is able to connect to control devices such as PLC, frequency inverter and temperature controller, which can be said to be a programmable application solution that is cost-friendly and highly reliable.

Applications :
Single control unit, landscape fountain, building automation

• Specifications :
  MPU points: 10/ 14 / 16 / 24 / 32 / 60
• Max. I/O points: 60
• Program capacity: 4k steps
• COM ports: Built-in RS-232 and RS-485 ports (available in 16-60 point models); compatible with Modbus ASCII/RTU protocol
• Built-in 4 points of high-speed counters*:

PLC Delta DVP-20PM

The advanced PM series motion control MPU can become the motion extension module of another PM series MPU, very flexible in all kinds of applications.

Applications :
Used for 2-axis servo positioning control, material cutting machine (high-speed servo control), crane operations, material clipper controlled by the servo.

Specifications :

• MPU points: 16
• Max. I/O points: 512
• Program capacity: 64K Steps
• Communication port: Built-in RS-232 and RS-485, compatible with MODBUS ASCII / RTU communication protocol.
• Data register: 10,000 words (latched)
• 500KHz high-speed pulse output:
  Built-in 2 groups of A/B phase differential signal ouput
  X-axis pulse output: (FP0+, FP0-), (RP0+, RP0-)
  Y-axis pulse output: (FP1+, FP1-), (RP1+, RP1-)
• Supports Manual Pulse Generator (MPG) and multi-point external signal inputs

PLC Delta DVP-15MC

DVP15MC11T is a type of multi-axis motion controller researched and produced by Delta autonomously on basis of CANopen field bus. It complies with CANopen DS301 basic communication protocol and DSP402 motion control protocol. In addition, it also supports standard instruction libraries defined by international organizations for motion control. It brings great convenience to user to learn and develop projects quickly. Maximum 24 axes can be controlled by means of Motion port. The single-axis motion instructions including velocity, position, torque and homing instructions as well as multi-axis instructions such as electronic gear, electronic cam, rotary cut and G code are supported.

Applications :

High-speed Cutting Machine, Digital Board Cutting Machine, CNC Lathe

Features & Benefits :

• Up to 24 real axes control (virtual axis no.: 1 ~ 32, can’t be repetitive with real axis no.)
• Built-in motion control instructions (supporting Jerk and BufferMode) and easy to use
• Supports encoder axis and virtual axis
• Single axis motion control instructions: speed, torque, homing, and position setup
• Application instructions: electronic gear, E-Cam, and rotary cut
• G-code: 8 axes linear / arc / helical interpolation
• Coordinates motion control instruction

Specifications :

• 1 GHZ high-speed floating point operation
• High-precision computing: supports LREAL (Double-precision floating -point format )
• Synchronization time: 4 axes in 2 ms / 8 axes in 4 ms
• Program capacity: 20 MB
• Data capacity: 20 MB
• 1 CANopen port as host or slave station
• 1 CANopen (Motion) communication port for motion control
• 16 high-speed inputs / 8 high-speed outputs
• 2 incremental encoder interfaces
• 1 SSI absolute encoder interface
• 2 Ethernet ports
• 1 SD card slot
• 1 RS-232 port and 1 RS-485 port
• Extension:
  • Left-side: Supports up to 8 DVP-S Series modules (master / slave / load cell modules)
  • Right-side: Compatible with DVP-S Series modules (240 I/O, 8 special modules)

PLC Delta DVP-10PM

This series highlights high-speed command execution speed (basic command LD for 0.1375μs, application command MOV for 2.1μs and 1MHz differential output*4) to achieve precise motion control.

Applications :

Used for 2-axis servo positioning control, material cutting machine (high-speed servo control), crane operations, material clipper controlled by the servo.

Specifications :

• MPU points: 24
• Max. I/O points: 256
• Program capacity: 64k steps
• Built-in hardware digital filter for counting
• 6 high-speed counters (O.C. 200kHz*4, differential 200kHz*2), supporting U/D, U/D Dir, A/B, 4A/B counting modes
• 4 differential 1MHz outputs, supporting U/D, U/D Dir, A/B output modes
• Supports 1-speed (immediate stop after the mark arrives), 2-speed, zero return, MPG and single axis function
• Highly accurate PWM 200kHz output, resolution 0.3%
• Electronic gear function
• 8 high-speed captures (mark correction, frequency measurement), comparative output, mark/mask function (for bag making)
• 8 external interruptions for setting up rising- and falling-edge triggers, 1 timed interruption
• Highly efficient command execution. LD: 0.1375μs, MOV: 2.1μs

PLC Delta DVP-10MC

Features & Benefits :

• Up to 16 axes can be controlled through high-speed CANopen communication
• Provides E-Cam (2048 points), rotary cut and flying shear applications
• Compatible with DVP-S series left and right side modules for flexible applications

Application :
packaging machinery, rotary cut machines, panel saws, coil winding machines and bag making machines.

Specifications :

• Built-in 12 I/O points(8 sets of high-speed pulse inputs for interrupt function and 4 sets of high-speed outputs)
• Max. 480 I/O points
• Program capacity：Ladder 16k steps / Motion 1Mbyte
• Built-in Ethernet, RS-232 and RS-485 communication port and standard MODBUS ASCII/RTU communication protocol
• Flexible industrial network applications(provides DeviceNet Master/Slave, CANopen Master/Slave, PROFIBUS-DP Slave and many more modules)
• Provides standard CANopen communication cables, terminal resistors, distribution boxes and related accessories. Wiring is simple and easy.
• Synchronously controls 4 axes in 2ms and 8 axes in 4ms
• Compatible with G-Code
• Supports PLCopen standard function blocks for motion control, enhancing program editing efficiency

PLC Delta AS Series

Programmable logic controller (PLC) is a control system using electronic operations. Its easy storing procedures, handy extending principles, functions of sequential/position control, timed counting and input/output control are widely applied to the field of industrial automation control.

Delta’s DVP series programmable logic controllers offer high-speed, stable and highly reliable applications in all kinds of industrial automation machines. In addition to fast logic operation, bountiful instructions and multiple function cards, the cost-effective DVP-PLC also supports various communication protocols, connecting Delta’s AC motor drive, servo, human machine interface and temperature controller through the industrial network in to a complete “Delta Solution” for all users.

Compact Modular Mid-range PLC – AS Series

The Delta Compact Modular Mid-range PLC AS Series is a high performance multi-purpose controller designed for all kinds of automated equipment. It features Delta’s self-developed 32-bit SoC CPUs for enhanced execution speed (40 k steps/ms) and supports up to 32 extension modules or up to 1,024 inputs/outputs. The AS series provides accurate positioning control for up to 8 axes via CANopen motion network and max. 6 axes via pulse control (200 kHz). It is widely used in diverse automated equipment such as electronics manufacturing, labeling, food packaging, and textile machines.